Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B622 Grade UNS N10001

Product info

Supplier:	Tapgroup internation.,JSC
Address:	Số 32 Lô N4D, đường X2A, Yên Sở, Hoàng Mai, Hà Nội
Phone:	0084 933 86 77 86
Email:	info@tapgroup.vn
Website:	https://supplier-pipe-tube-ongthep.com
Insurance:	12 tháng
Status:	Mới 100%
Origin:	China, Korea, Malaysia, Thailand, Japan, EU, G7

Catalogue Profile

Description

Name:					Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube B622 Grade UNS N10001
Type Of Tubes:					SMLS Nickel and Nickel-Cobalt Alloy Pipe and Tube B622 Grade UNS N10001										Seamless Tube					SMLS Tube
					Seamless pipe, Nickel and Nickel-Cobalt Alloy B622 Grade UNS N10001										SMLS pipe, Nickel and Nickel-Cobalt Alloy B622 Grade UNS N10001
Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tubes This standard is issued under the fixed designation B622; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.


Scope
This specification covers seamless pipe and tubes of nickel and nickel-cobalt alloys (UNS N10001, UNS N10242, UNS N10665, UNS N12160, UNS N10675, UNS N10276, UNS N06455, UNS N06007, UNS N08320, UNS N06975, UNS N06002, UNS N06985, UNS N06022, UNS N06035, UNS N08135, UNS N06255, UNS N06058, UNS N06059, UNS N06200, UNS N10362, UNS N06030, UNS N08031, UNS R30556, UNS N08535, UNS N06250, UNS N06060, UNS N06230, UNS N06686, UNS N10629, UNS N06210, UNS N10624, and UNS R20033). Pipe and tube shall be supplied in the solution annealed and descaled condition. When atmosphere control is used, descaling is not necessary. This specification is limited to tubes up to and including 3.5 in. (88.9 mm) outside diameter. The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.








Chemical Requirements
	Ni	Cr	Mo	Fe	W	C	Si max	Co	Mn	V	P max	S max	Ti	Cu	Cb (Nb) +Ta	Al	Zr	La	N	B	Cb (Nb)	Ta	Ni+ Mo	Mg
Ni-Mo Alloys
N10001	remainder^A	1.0 max	26.0-30	4.0-6.0	…	0.05 max	1.0	2.5 max	1.0 max	0.2- 0.4	0.04	0.03	…	…	…
Hydrostatic Test or Non-Destructive Electric Test
Each pipe or tube shall be tested by the manufacturer by either hydrostatic or a non-destructive electric test in accordance with Specification B829. Hydrostatic testing at a pressure greater than 1000 psi may be performed upon agreement between the purchaser and manufacturer or at the option of the manufacturer provided that the allowable fiber stress per Specification B829 is not exceeded
Weight
Alloy													Density
													lb/in.³						g/cm3
Nickel-molybdenum:
UNS N10001													0.334						9.24
Mechanical Properties of Pipe and Tube
Alloy						Tensile Strength, min, ksi (MPa)							Yield Strength (0.2 % Offset) min, ksi (MPa)						Elongation in 2 in. (50.8 mm) or 4D,^A min, %
Ni-Mo
UNS N10001						100 (690)							45 (310)						40
^AD refers to the diameter of the tension specimen. ^BSolution annealed at a minimum temperature of 2200°F (1204°C) followed by a water quench or rapidly cooled by other means.

Pipe Schedules^A
Nominal Pipe Size, in.					Outside Diameter					Schedule No. 10					Nominal Wall Thickness Schedule No. 40					Schedule No. 80
Inches
¹⁄₄					0.540					0.065					0.088					…
³⁄₈					0.675					0.065					0.091					0.126
¹⁄₂					0.840					0.083					0.109					0.147
³⁄₄					1.050					0.083					0.113					0.154
1					1.315					0.109					0.133					0.179
1¹⁄₄					1.660					0.109					0.140					0.191
1¹⁄₂					1.900					0.109					0.145					0.200
2					2.375					0.109					0.154					0.218
2¹⁄₂					2.875					0.120					0.203					0.276
3					3.500					0.120					0.216					0.300
Millimetres
¹⁄₄					13.72					1.65					2.24					…
³⁄₈					17.14					1.65					2.31					3.20
¹⁄₂					21.34					2.11					2.77					3.73
³⁄₄					26.67					2.11					2.87					3.91
1					33.40					2.77					3.38					4.55
1¹⁄₄					42.16					2.77					3.56					4.85
1¹⁄₂					48.26					2.77					3.68					5.08
2					60.32					2.77					3.91					5.54
2¹⁄₂					73.02					3.05					5.16					7.04
3					88.90					3.05					5.49					7.62
^A The pipe schedules shown conform with standards adopted by the American National Standards Institute.

Product info

Mr. Thi

Ms. Hoa

Ms. Phương

Ms. Trinh

Ms. Trân

Social network