Seamless Tube 11CrMo9-10, EN 10216-2

Product info

Supplier:	Tapgroup internation.,JSC
Address:	Số 32 Lô N4D, đường X2A, Yên Sở, Hoàng Mai, Hà Nội
Phone:	0084 933 86 77 86
Email:	info@tapgroup.vn
Website:	https://supplier-pipe-tube-ongthep.com
Insurance:	12 tháng
Status:	Mới 100%
Origin:	China, Korea, Malaysia, Thailand, Japan, EU, G7

Catalogue Profile

Description

Name:

Seamless Tube 11CrMo9-10, EN 10216-2

"Product alias"

Seamless pipe 11CrMo9-10, EN 10216-2

SMLS pipe 11CrMo9-10, EN 10216-2

SMLS Tube, 11CrMo9-10, EN 10216-2

Heat treatment conditions

Steel grade

Heat treatment a

Austenizing

Tempering

Steel name

Steel number

Temperature °C

Cooling Medium

Temperature °C

Cooling Medium

11CrMo9-10

1.7383

+QT

900 to 960

không khí hoặc chất lỏng

680 to 750

air

^a +N = Normalising, +NT = Normalising + Tempering, +QT = Quenching + Tempering (air or liquid), +I = Isothermal Annealing.

^b Normalising includes Normalising Forming.

^c For these steel grades it may be necessary in the case of wall thickness T above 25 mm or T/D > 0,15 to apply quenching and tempering in order to achieve the intended structure and material properties . The decision shall be left to the discretion of the manufacturer but shall be stated to the customer at the time of enquiry and order. Steel tubes treated in such a way shall be designated by the steel name supplemented by the symbol +QT .

Table 2 Chemical compposition (cast analysis)^a, in % by mass

Steel grade

Pmax

Smax

Almax

Ti max

Cr+Cu+Mo+Ni

Others

Steel name

Steel number

11CrMo9-10

1.7383

0.06 to 0.15

≤0.5

0.4 to 0.8

0.025

0.02

2.0 to 2.5

0.9 to 1.1

≤0.30

≤0.04

≤0.30^C

–

^a Element not included in this table shall not be intensionally to the steel without the agreenent of the purchaser, except for elements which may be added for finishing the cast. All appropriate shall be taken to prevent the addition of unsirable elements from scrap or other materialss used in the steel making process.
^b This requirement is not applicable provided steel contains a sufficient amont of then nitrogen binding elements which shall be reported. When using titanium, the producer shall verify that (Al+Ti)≥0.02%
^cOption 2: In order to faciliate subsequent forming operations, an agreed maximum copper content lower than indicated and an agreed specified maximum tin content shall apply
^dThe content of these elements need not to be reported unless intensionally added to the cast.
^eFor wall thickness≥30mm the carbon content may be increased by 0.02% for the cast and product analysis.
The upper carbon value of 0.23% shall not be exceeded for product analysis.

Permissible deviations of the product analysis from specified limits on cast analysis given

Element

Limiting value for the cast analysis in accordance with Table 2 % by mass

Permissible deviation of the product analysis % by mass

≤0.29

±0.02

≤0.40

±0.05

>0.40 to ≤1.00

±0.06

≤1.00

±0.05

>1.00 to ≤1.50

±0.1

≤0.025

±0.005

≤0.10

±0.003

>0.01 ≤0.02

±0.005

≤0.06

±0.005

≤0.006

±0.001

≤1.00

±0.05

>1.00 to ≤ 10.00

±0.1

>10.00 to ≤ 12.5

±0.15

≤0.80

±0.05

≤0.35

±0.03

>0.35 to ≤1.20

±0.04

≤0.070

±0.01

≤0.10

±0.005

≤0.35

±0.05

>0.35 to ≤1.30

±0.07

≤0.060

±0.01

≤0.10

±0.01

>0.10 to ≤0.55

±0.03

Mechanical properties
Mechanical properties at and below room temperature
The mechanical properties at and below room temperature of the tubes shall conform to the requirements in Table 4 and in clauses 11.3, 11.4, 11.5 and 11.6.
Proof strength at elevated temperature
The minimum proof strength Rp0,2 values at elevated temperature are given in Table 5.
Option 6: Proof strength Rp0,2 shall be verified. The test temperature shall be specified at the time of enquiry and order.
Creep rupture strength
The creep rupture strength values are given in annex A for information
Appearance and internal soundness

Mechanical properties

Steel grade

Tensile properties at room temperature

Impact properties ^{a b}

Steel name

Steel number

Upper yield strength or proof strength R_eHfor wall thickness Tmin

Tensile strength Rm

Elongation A min.%a

Minimum average absorbed energy KV J at a temperature of °C

T≤16

16<T≤40

40<T≤60

60<T≤100

Mpa*

-10

11CrMo9-10

1.7383

355

–

540 to 680

40^C

–

27^C

–

^a l = longitudinal t = transverse
^b To be verified when options 4 and/or 5 are/is specified, unless footnote f) applies.
^cOption 4: Impact energy shall be verified.
^d Option 5: Longitudinal impact energy shall be verified.
^eFor wall thickness 60mm <T≤80 mm.
^fImpact test mandatory for wall thickness T≥1600.
MPa = 1N/m²

Minimum proof strength R_p0.2at elevated temperature

Steel grade

Wall thickness mm

Minimum proof strength R_p0.2Mpa^aat temperature of °C

Steel name

Steel number

100

150

200

250

300

350

400

450

500

550

600

11CrMo9-10

1.7383

≤60

323

312

304

296

289

280

275

257

239

–

^a1 Mpa = 1 N/mm²

Dimensions EN 10216-2

dimensions in mm

Outside
diameter D
Series^a

Wall thickness T

1.6

1.8

2.3

2.6

2.9

3.2

3.6

4.5

5.6

6.3

7.1

8.8

12.5

14.2

10.2

12.7

13.5

17.2

21.3

25.4

26.9

31.8

33.7

42.4

44.5

48.3

60.3

63.5

76.1

82.5

88.9

101.6

108

114.3

127

133

139.7

141.3

152.4

159

168.3

177.8

193.7

219.1

244.5

273

323.9

355.6

406.4

457

508

559

610

660

711

Outside
diameter D
Series^a

Dimensions EN 10216-2
Wall thickness T
dimensions in mm

17.5

22.2

100

10.2

12.7

13.5

17.2

21.3

25.4

26.9

31.8

33.7

42.4

44.5

48.3

60.3

63.5

76.1

82.5

88.9

101.6

108

114.3

127

133

139.7

141.3

152.4

159

168.3

177.8

193.7

219.1

244.5

273

323.9

355.6

406.4

457

508

559

610

660

711

^aseries 1 = diameters for which all the accessories needed for the construction of piping system are standardized;
series 2 = diameters for which not all the accessories are standardized;
series 3 = diameters for special application for which very few standardized accessories exist.

Tolerance on outside diameter and wall thickness

Outside Diameter D mm

Tolerances on D

Tolerance on T for a T/D ratio

≤0.025

>0.025≤0.050

>0.050≤ 0.10

>0.10

D ≤ 219.1

±1 % or ±0.5mm whichever is the greater

± 12,5% or ± 0.4mm whichever is the greater

D > 219.1

± 20%

± 15%

± 12.5%

± 10%^a

^aFor outside diameters D≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5% of the
wall thickness T

Tolerance on inside diameter and wall thickness

Tolerances on inside diameter

Tolerances on T for a T/d ratio

d_min

≤0.03

>0.03≤0.06

>0.06≤ 0.12

>0.12

± 1% or ± 2mm whichever is the greater

±2% + 4 mm whichever or is the greater

± 20%

± 15%

± 12.5%

± 10%^a

^aFor outside diameters D≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5% of the
wall thickness T

Tolerances on outside diameter and minimum wall thickness

Outside Diameter D mm

Tolerances on D

Tolerance on T for a T/D ratio

≤0.02

>0.02≤0.040

>0.040≤ 0.09

>0.09

D ≤ 219.1

±1 % or ±0.5mm whichever is the greater

+28% or +0.8 mm whichever is the greater

D > 219.1

± 50%

± 35%

± 28%

± 22%^a

^aFor outside diameters D≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5% of the
wall thickness T

Table 10 Tolerances on inside diameter and minimum wall thickness

Tolerances on inside diameter

Tolerances on T_minfor a T_min/d ratio

d_min

≤0.05

>0.05≤0.1

>0.1

± 1% or ± 2mm whichever is the greater

±2% + 4 mm whichever or is the greater

± 35%

± 28%

± 22%^a

^aFor outside diameters D≥ 355,6 mm it is permitted to exceed the upper wall thickness locally by a further 5% of the
wall thickness T

Tolerances on outside diameter and wall thickness for tube ordered cold finished

Tolerance on D

Tolerance on T

±0.5% or ± 0.3 mm whichever or is the greater

± 10% or ± 0.2 mm whichever or is the greater

Tolerances on exact lengths
The tolerances for exact lengths shall be as given

Tolerances on exact lengths

Dimension in mm

Length L

Tolerance on exact length

L ≤ 6000

+10%

6000 < L ≤ 12000

+15%

L > 12000

+ by agreement

Flattening test – Constant factor of deformation C

Steel grade

Steel name

Steel number

11CrMo9-10

1.7383

0.07

After testing, the test piece shall be free from cracks or breaks. However, slight incipient cracks at its edges shall not be regarded as justification for rejection.
Ring tensile test
The test shall be carried out in accordance with EN 10237. The tube section shall be subjected to strain in the circumferential direction until fracture occurs. After fracture the test pieces shall not show any visible cracks without the use of magnifying aids (excluding the fracture point).
Drift expanding test
The test shall be carried out in accordance with EN 10234. The tube section shall be expanded with a 60° conical tool until the percentage increase in outside diameter shown

Drift expanding test requirements

Steel grade

% increase in outside diameter for d/D ^a

Steel name

Steel number

≤ 0.6

> 0.6 ≤ 0.8

> 0.8

11CrMo9-10

1.7383

Creep rupture strength values
The creep rupture strength values of steel grades covered by this Part of EN 10216 are given

Creep rupture strength values

Steel grade

Temperature °C

Creep rupture strength values for (MPa ) a b c d

Steel name

Steel number

10 000 h

100 000 h

200 000 h

250 000 h

11CrMo9-10

400

382

313

410

355

269

420

333

272

430

312

255

440

294

238

450

276

221

460

259

204

470

242

187

480

225

170

490

208

153

500

191

137

510

174

122

520

157

107

^aThe values listed in the Table are values suggested by ECCC (1) and are average values from scatter range determined from existing data which will be assessed from time to time after test results are available and corrected if necessary. The values for the steel grades 14MoV6-3 and X10CrMoVNb9-1 have been obtained by new evaluation. For the remaining steel grades the values were obtained from creep rupture strength values given in national and international standards
^b The creep rupture strength values given up to the elevated temperature listed in the Table, do not mean that the steels can be used in continuous duty up to the these temperatures. A governing factor is the total stress during operation.
^c For the creep rupture strength values indicated in the Table the extrapolation times are always less than a factor of three unless indicated by an asterisk (*).
^d1 MPa = 1 N/mm2

Product info

Mr. Thi

Ms. Hoa

Ms. Phương

Ms. Trinh

Ms. Trân

Social network